![]() Worth noting there seems to be a ECU flash update that address some of the issues but for me I haven't been to the dealer since I bought the Himy and have no plans on ever returning to dealer. I made the changes one at a time to see which one(s) had the biggest impact on the drivability and general starting etc. I let it do this until I reached the 300 mile service - during the 300 mile service I made a series of changes that have been working well for over fifteen-hundred miles. ![]() start.Īlso experienced heat soak cut off - meaning if I road the bike for 40min or so then parked it say to grab lunch then once restarted it would stall out/die - I've later discovered this was due to the IAT getting heat soaked and giving a much higher temp reading resulting in ECU even cutting the fuel more (lean) since it was in running in fueling condition 1. Building custom mapping on our dyno is what we specialize in, so we are CONSTANTLY creating new custom mapping as new motorcycle models, intake and exhaust systems are released.Like so many my Himy suffered from the dreaded .start.die. On top of all of that, we offer FREE mapping updates for any future modifications you make to your motorcycle AND any improvements we make to our custom mapping through our constant R&D process. The combination of the custom fuel and ignition mapping that we build for each setup on the dyno, in conjunction with our custom throttle mapping, provides the smoothest AND strongest engine operation possible throughout the ENTIRE RPM range. If you want to remove the system entirely, you can do so without issue once we flash the ECU, and you can simply install block off plates in place of the system!Ī: In the past decade, we have flashed more motorcycle ECU’s than anyone else on the planet for one main reason: ALL of our custom fuel and ignition mapping is built specifically for each motorcycle and intake/exhaust combination that we offer flashing support for! For throttle-by-wire motorcycles, our custom throttle mapping has been developed after thousands of hours of feedback and testing from riders on the street AND professional racers on the track. In these cases (most motorcycles fall into this category) the AIS/PAIR solenoid feed line should be plugged with a vacuum cap to prevent air from flowing from the airbox to the air injection system. In some cases, the AIS/PAIR solenoids used are “naturally closed”, which means that when we disable this system through ECU flashing software, the solenoid remains closed and now air can pass through the system! Unfortunately, most AIS/PAIR solenoids are “naturally open”, so when the system is disabled the solenoid still allows air to pass through the system. It also negatively impacts throttle response and smoothness by interrupting your engine’s normal exhaust pulse flow. It may sound cool, but is quite hard on the exhaust valves and will eventually blow the packing right out of your muffler. BUILDING CUSTOM MAPPING ON OUR DYNO IS WHAT WE SPECIALIZE IN, SO WE ARE CONSTANTLY CREATING NEW CUSTOM MAPPING AS NEW MOTORCYCLE MODELS, INTAKE AND EXHAUST SYSTEMS ARE RELEASED.Ī: In most cases, your bike’s AIS/PAIR system (the stock air-injection system equipped on most modern motorcycles for emissions compliance) should absolutely be removed, plugged or blocked off in some way! Once an aftermarket performance exhaust system (without a catalytic converter) is installed on your bike, this system will cause significant backfiring on deceleration. ON TOP OF ALL OF THAT, WE OFFER FREE MAPPING UPDATES FOR ANY FUTURE MODIFICATIONS YOU MAKE TO YOUR MOTORCYCLE AND ANY IMPROVEMENTS WE MAKE TO OUR CUSTOM MAPPING THROUGH OUR CONSTANT R&D PROCESS. THE COMBINATION OF THE CUSTOM FUEL AND IGNITION MAPPING THAT WE BUILD FOR EACH SETUP ON THE DYNO, IN CONJUNCTION WITH OUR CUSTOM THROTTLE MAPPING, PROVIDES THE SMOOTHEST AND STRONGEST ENGINE OPERATION POSSIBLE THROUGHOUT THE ENTIRE RPM RANGE. IN THE PAST DECADE, WE HAVE FLASHED MORE MOTORCYCLE ECU'S THAN ANYONE ELSE ON THE PLANET FOR ONE MAIN REASON: ALL OF OUR CUSTOM FUEL AND IGNITION MAPPING IS BUILT SPECIFICALLY FOR EACH MOTORCYCLE AND INTAKE/EXHAUST COMBINATION THAT WE OFFER FLASHING SUPPORT FOR! FOR THROTTLE-BY-WIRE MOTORCYCLES, OUR CUSTOM THROTTLE MAPPING HAS BEEN DEVELOPED AFTER THOUSANDS OF HOURS OF FEEDBACK AND TESTING FROM RIDERS ON THE STREET AND PROFESSIONAL RACERS ON THE TRACK.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |